ENGINETECH : BC409J |
Crankshaft Main Bearing |
|
MAHLE / CLEVITE : MS2199A |
Crankshaft Main Bearing |
- A
Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M
Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- AL
Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N
Narrowed for greater crankshaft fillet clearance. ;
- B
Steel backed bearings with a conventional babbit lining.: P
Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- C
Steel backed bearings with a copper-lead lining.: R
Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- D
Bearing has dowel hole.: S
Indicates a set number designation. ;
- G
Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V
High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- H
High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG
High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HG
High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X
Bearing has .001” more oil clearance than standard. ;
- HT
High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX
Bearing has .002” more oil clearance than standard. ;
- K
TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W
Indicates a part that is a thrust washer (may also be designated upper or lower). ;
|
SEALED POWER : 7298MA |
Crankshaft Main Bearing |
- Displacement: 346 LS1 ;
- Engine Family: Gen III V8 ;
- Manufacture: Chevrolet ;
- Material: A-Series aluminum bearings ;
- Part Material: A-Series aluminum ;
- Set Type: Main Set ;
|
MAHLE / CLEVITE : MS2199P |
Crankshaft Main Bearing |
- A
Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M
Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- AL
Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N
Narrowed for greater crankshaft fillet clearance. ;
- B
Steel backed bearings with a conventional babbit lining.: P
Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- C
Steel backed bearings with a copper-lead lining.: R
Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- D
Bearing has dowel hole.: S
Indicates a set number designation. ;
- G
Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V
High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- H
High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG
High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HG
High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X
Bearing has .001” more oil clearance than standard. ;
- HT
High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX
Bearing has .002” more oil clearance than standard. ;
- K
TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W
Indicates a part that is a thrust washer (may also be designated upper or lower). ;
|
MAHLE / CLEVITE : MS2366A |
Crankshaft Main Bearing |
- A
Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M
Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- AL
Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N
Narrowed for greater crankshaft fillet clearance. ;
- B
Steel backed bearings with a conventional babbit lining.: P
Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- C
Steel backed bearings with a copper-lead lining.: R
Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- D
Bearing has dowel hole.: S
Indicates a set number designation. ;
- G
Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V
High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- H
High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG
High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HG
High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X
Bearing has .001” more oil clearance than standard. ;
- HT
High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX
Bearing has .002” more oil clearance than standard. ;
- K
TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W
Indicates a part that is a thrust washer (may also be designated upper or lower). ;
|
ITM ENGINE COMPONENTS : 5M6956 |
Crankshaft Main Bearing |
|
SEALED POWER : 152M |
Crankshaft Main Bearing |
|
MAHLE / CLEVITE : MS2199H |
Crankshaft Main Bearing |
- A
Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M
Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- AL
Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N
Narrowed for greater crankshaft fillet clearance. ;
- B
Steel backed bearings with a conventional babbit lining.: P
Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- C
Steel backed bearings with a copper-lead lining.: R
Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- D
Bearing has dowel hole.: S
Indicates a set number designation. ;
- G
Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V
High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- H
High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG
High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HG
High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X
Bearing has .001” more oil clearance than standard. ;
- HT
High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX
Bearing has .002” more oil clearance than standard. ;
- K
TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W
Indicates a part that is a thrust washer (may also be designated upper or lower). ;
|
GM GENUINE : 89017571 |
Crankshaft Main Bearing |
|
ENGINETECH : BC204J |
Crankshaft Main Bearing |
- Maximum Clearance: 0.0009-0.0033 ;
- Maximum Housing Inside Diameter: 3.3464-3.3472 ;
- Position: 1-2-3-4-5 ;
- Shaft Diameter: 3.1459-3.1466 ;
- Shell Part Number: MB-3776P ;
- Wall Thickness: 0.0990-0.0995 ;
- Width: 0.820 ;
|
MAHLE / CLEVITE : MS2218P |
Crankshaft Main Bearing |
- A
Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M
Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- AL
Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N
Narrowed for greater crankshaft fillet clearance. ;
- B
Steel backed bearings with a conventional babbit lining.: P
Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- C
Steel backed bearings with a copper-lead lining.: R
Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- D
Bearing has dowel hole.: S
Indicates a set number designation. ;
- G
Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V
High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- H
High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG
High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HG
High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X
Bearing has .001” more oil clearance than standard. ;
- HT
High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX
Bearing has .002” more oil clearance than standard. ;
- K
TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W
Indicates a part that is a thrust washer (may also be designated upper or lower). ;
|
SEALED POWER : 7429M |
Crankshaft Main Bearing |
- Part Material: Steel backed overplated bronze alloy ;
|
MAHLE / CLEVITE : MS2218H |
Crankshaft Main Bearing |
- A
Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M
Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- AL
Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N
Narrowed for greater crankshaft fillet clearance. ;
- B
Steel backed bearings with a conventional babbit lining.: P
Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- C
Steel backed bearings with a copper-lead lining.: R
Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- D
Bearing has dowel hole.: S
Indicates a set number designation. ;
- G
Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V
High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- H
High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG
High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HG
High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X
Bearing has .001” more oil clearance than standard. ;
- HT
High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX
Bearing has .002” more oil clearance than standard. ;
- K
TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W
Indicates a part that is a thrust washer (may also be designated upper or lower). ;
|
GM GENUINE : 89065022 |
Crankshaft Main Bearing |
- Outside Diameter (IN): 3.8 ;
- Outside Diameter (MM): 96.65 ;
- Sealed: No ;
- Shaft Diameter (IN): 2.75 ;
- Shaft Diameter (MM): 69.984 ;
- Width (IN): 0.99 ;
- Width (MM): 25.27 ;
|
GM GENUINE : 89060394 |
Crankshaft Main Bearing |
- Outside Diameter (IN): 3.07 ;
- Outside Diameter (MM): 78.18 ;
- Sealed: No ;
- Width (IN): 0.81 ;
- Width (MM): 20.68 ;
|
MAHLE / CLEVITE : MS2250A |
Crankshaft Main Bearing |
- A
Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M
Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- AL
Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N
Narrowed for greater crankshaft fillet clearance. ;
- B
Steel backed bearings with a conventional babbit lining.: P
Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- C
Steel backed bearings with a copper-lead lining.: R
Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- D
Bearing has dowel hole.: S
Indicates a set number designation. ;
- G
Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V
High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- H
High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG
High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HG
High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X
Bearing has .001” more oil clearance than standard. ;
- HT
High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX
Bearing has .002” more oil clearance than standard. ;
- K
TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W
Indicates a part that is a thrust washer (may also be designated upper or lower). ;
|
MAHLE / CLEVITE : MS2382PK |
Crankshaft Main Bearing |
- A
Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M
Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- AL
Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N
Narrowed for greater crankshaft fillet clearance. ;
- B
Steel backed bearings with a conventional babbit lining.: P
Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- C
Steel backed bearings with a copper-lead lining.: R
Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- D
Bearing has dowel hole.: S
Indicates a set number designation. ;
- G
Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V
High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- H
High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG
High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HG
High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X
Bearing has .001” more oil clearance than standard. ;
- HT
High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX
Bearing has .002” more oil clearance than standard. ;
- K
TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W
Indicates a part that is a thrust washer (may also be designated upper or lower). ;
|
MAHLE / CLEVITE : MS2382P |
Crankshaft Main Bearing |
- A
Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M
Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- AL
Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N
Narrowed for greater crankshaft fillet clearance. ;
- B
Steel backed bearings with a conventional babbit lining.: P
Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- C
Steel backed bearings with a copper-lead lining.: R
Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- D
Bearing has dowel hole.: S
Indicates a set number designation. ;
- G
Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V
High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- H
High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG
High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HG
High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X
Bearing has .001” more oil clearance than standard. ;
- HT
High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX
Bearing has .002” more oil clearance than standard. ;
- K
TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W
Indicates a part that is a thrust washer (may also be designated upper or lower). ;
|
MAHLE / CLEVITE : MS2218HXC |
Crankshaft Main Bearing |
|
MAHLE / CLEVITE : MS2218HX |
Crankshaft Main Bearing |
- A
Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M
Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- AL
Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N
Narrowed for greater crankshaft fillet clearance. ;
- B
Steel backed bearings with a conventional babbit lining.: P
Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- C
Steel backed bearings with a copper-lead lining.: R
Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- D
Bearing has dowel hole.: S
Indicates a set number designation. ;
- G
Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V
High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- H
High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG
High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HG
High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X
Bearing has .001” more oil clearance than standard. ;
- HT
High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX
Bearing has .002” more oil clearance than standard. ;
- K
TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W
Indicates a part that is a thrust washer (may also be designated upper or lower). ;
|
MAHLE / CLEVITE : MS2218HC |
Crankshaft Main Bearing |
|
MAHLE / CLEVITE : MS2199HXC |
Crankshaft Main Bearing |
|
MAHLE / CLEVITE : MS2199HX |
Crankshaft Main Bearing |
- A
Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M
Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- AL
Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N
Narrowed for greater crankshaft fillet clearance. ;
- B
Steel backed bearings with a conventional babbit lining.: P
Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- C
Steel backed bearings with a copper-lead lining.: R
Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- D
Bearing has dowel hole.: S
Indicates a set number designation. ;
- G
Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V
High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- H
High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG
High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HG
High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X
Bearing has .001” more oil clearance than standard. ;
- HT
High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX
Bearing has .002” more oil clearance than standard. ;
- K
TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W
Indicates a part that is a thrust washer (may also be designated upper or lower). ;
|
ENGINETECH : BC126J |
Crankshaft Main Bearing |
|
ENGINETECH : BC102J |
Crankshaft Main Bearing |
|
SEALED POWER : 7370M |
Crankshaft Main Bearing |
- Design Feature 2: 3/4 grooved ;
|
MAHLE / CLEVITE : MS2091P |
Crankshaft Main Bearing |
- A
Steel backed lead free aluminum silicon alloy bearings without overlay. Standard replacement material.: M
Steel backed bearings with a Micro-Babbitt lining (a very thin layer of lining which reduces the microscopic deflections that occur to a bearing when loaded and thus increases fatigue life). Solely intended for extreme high-horsepower applications. ;
- AL
Solid cast aluminum alloy bearings (material designation AL-1) or steel backed bearings with an aluminum alloy lining material designation AL-3, AL-4, AL-5, AL-6). Standard replacement material.: N
Narrowed for greater crankshaft fillet clearance. ;
- B
Steel backed bearings with a conventional babbit lining.: P
Steel backed bearings with an intermediate layer of copper-lead alloy and an electroplated lead-tin-copper overlay. Standard replacement material. ;
- C
Steel backed bearings with a copper-lead lining.: R
Indicates that the bearing can be resized to standard. When following a camshaft bearing, indicates that it has extra bore stock in the inside diameter. ;
- D
Bearing has dowel hole.: S
Indicates a set number designation. ;
- G
Steel backed bearings with a matrix of copper and an infiltrant of lead-tin babbitt. Precision undersizes are not resizable.: V
High performance bearing with a lead-indium overlay (on main sets this indicates partial groove). Solely intended for extreme high-horsepower applications. ;
- H
High performance bearing (on main sets this indicates partial groove). Perform the same as "A" and "P" bearings, but have the ability to carry more load.: VG
High performance bearing with a lead-indium overlay and a full annular groove. Solely intended for extreme high-horsepower applications. ;
- HG
High performance full annular grooved bearing. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: X
Bearing has .001” more oil clearance than standard. ;
- HT
High performance with indentless locating lug. “Full Bore” design. Perform the same as "A" and "P" bearings, but have the ability to carry more load.: XX
Bearing has .002” more oil clearance than standard. ;
- K
TriArmor™ coating applied to the bearing surface, which offers extraordinary protection and lubricity. Enhanced wear characteristics increase bearing life in race engines and high performance street Engines.: W
Indicates a part that is a thrust washer (may also be designated upper or lower). ;
|